DI boxes

Active 2 channel DI box & splitter

Dual re-amping direct box

Review: The Dual RDB is the ideal interface solution for any application where stereo or dual line level signals from recording interfaces, computers, mixers, iPods, consumer audio or video machines need to be connected to XLR microphone or 1/4" instrument level inputs.

The unit has 2 x high quality isolation transformers that prevent ground loops when connecting various systems together.

The Dual RDB accepts 1/4" TRS and XLR line level inputs and outputs mic or instrument levels. The Dual RDB's variable level controls allow volume control to be set at the source rather than in the studio, AV room, audio closet or installation rack. A 20Hz to 20 kHz frequency response ensures the Dual RDB will function transparently with any high quality audio source.

Dual channel active direct box, comes with super quality battery

Review: The DUALXDirect provides 2 x independent high quality active interfaces that let you connect instrument, line, or speaker level signals to a mixer or other balanced inputs. Each of the high impedance 1/4" and XLR inputs (provided via combo jacks) are buffered and converted by very low noise active electronics into an isolated, balanced, low impedance signal output. The DUALXDirect has an extremely flat and wide frequency response and can handle high signal levels. This gives the DUALXDirect a very clean and neutral sound with a wide variety of signal sources and over long signal runs in high noise environments.

The input attenuator switches allow for a wide range of signal levels and the input Thru jacks allow for tapping off of your signal chain. The ground lift switches let you totally separate the input and output signal grounds, when appropriate, to isolate 2 systems, thereby reducing hum and ground-loop noise.

The DUALXDirect's active circuitry is powered by phantom voltage from the output connections or by an internal 9V battery, when external power is not available. When powered by a battery, it draws less than 7.5 mA which should provide more than 100 hours of operation with a new battery (alkaline recommended). If phantom power is available, then the DUALXDirect will automatically draw its power from the external source. The power on/off switch lights more dimly when the unit is running off of the battery, lights more brightly when it is running off of phantom power, and is off when the unit is inactive.

The compact black-anodized all aluminum case and it's active design allow the DUALXDirect to provide years of trouble free service in live sound, permanent/fixed install, DJ, and virtually any PA application. It's full feature set, rugged construction, and high-end specifications make the DUALXDirect the obvious choice.

The Art ARTcessories DUALXDirect features

Fully active design
Phantom voltage or 9V battery powered
Converts high-impedance balanced / unbalanced inputs into 600 Ohm balanced outputs
Switchable input attenuation (0, -30 dB)
Switchable ground lift
1/4" TRS / XLR combo connector inputs
XLR connectors for balanced outputs
Rugged extruded aluminum case
Frequency Response: 10 Hz - 100 kHz, i 0.5 dB @ +0 dBu
THD: <.05% (typical)
Dynamic Range: >100 dB (typical)
Channel Separation: > 80 dB (typical)
Maximum Input Level: +4, +34 dBu
Maximum Output Level: +6 dBu (battery powered), +14 dBu (phantom powered)
Input Connections: 1/4" TRS XLR female balanced / unbalanced (2), 470k Ohm
Thru Connections: 1/4" TRS (2)
Output Connections: XLR male balanced (2), <600 Ohm
Input Attenuation: Switchable, (0, -30 dB)
Power Requirements: 9V @ 7.5 mA (battery, alkaline recommended), 18 - 48V DC @ 6.4 mA (phantom power per channel)
Dimensions (DWH mm): 99 x 117 x 47
Weight: 0.38kg

2 x passive interfaces let you connect instrument, line or speaker level signals to a mixer or other balanced inputs

Review: The DUALZDirect provides 2 x independent high quality totally passive interfaces that let you connect instrument, line, or speaker level signals to a mixer or other balanced inputs through high performance audio isolation transformers. Each of the high impedance single-ended 1/4" inputs is converted by a transformer into an isolated, balanced, low impedance signal output. The DUALZDirect's audio transformers have an extremely flat and wide frequency response and can handle high signal levels. This gives the DUALZDirect a very clean and neutral sound with a wide variety of signal sources and over long signal runs in high noise environments.

The input attenuator switches allow for a wide range of signal levels and the input Thru jacks allows for tapping off of your signal chain. The ground lift switches let you totally separate the input and output signal grounds, when appropriate, to isolate 2 x systems, thereby reducing hum and ground-loop noise.

What further sets the DUALZDirect apart from other DI boxes are its extended features and versatility. Art have added switchable low pass filters that cut out all very high frequency interference. These Bessel filters on the outputs are placed out of the audio range and are primarily intended to reduce radio frequency interference before it gets into the main system. The filters are also very effective in reducing any digital computer noise artifacts when using the DUALZDirect as an interface between a computer-based audio workstation and your monitors. The pase invert switches, while not normally included with your run of the mill DI box, have been added to allow you to switch signal polarity right at the source. This feature is especially handy when you are combining a direct tap with a microphone feed in the mix.

The compact black-anodized all aluminum case and it's passive design allow the DUALZDirect to provide years of trouble free service in live sound, permanent/fixed Install, DJ, and virtually any PA application. It's full feature set, rugged construction, and high-end specifications make the DUALZDirect the obvious choice.

Active interface for connecting instrument, line, or speaker level signals to any balanced input, comes with super quality battery

Review: The Xdirect is a high quality interface that lets you connect instrument, line, or speaker level signals to a mixer or other balanced input. The high impedance single-ended 1/4" and XLR inputs are buffered and converted, by very low noise active electronics, into an isolated balanced low impedance signal source. The Xdirect has an extremely flat and wide frequency response and can handle high signal levels while still maintaining an isolated balanced low impedance output. This gives the Xdirect a very clean and neutral sound with a wide variety of signal sources and over long signal runs in high noise environments.

The input attenuator switches allow for a wide range of signal levels and the input link jack allows for tapping off of your signal chain. The ground lift switch lets you totally separate the input and output signal grounds, when appropriate, to isolate 2 systems, thereby reducing hum and ground-loop noise.

What further sets the Xdirect apart from other Active DI boxes are its extended features and versatility. ART have added a switchable low pass filter that cuts out all very high frequency interference. This bessel filter on the input is placed out of the audio range and is primarily intended to reduce radio frequency interference before it gets into the main system. The filter is also very effective in reducing any digital computer noise artifacts when using the Xdirect as an interface between a computer based audio workstation and your monitors.

A phase invert switch, while not normally included with your run of the mill D.I. box, has been added to allow you to switch signal polarity right at the source. This feature is especially handy when you are combining a direct tap with a microphone feed in the mix.

The Xdirects active circuitry is powered by an internal 9V battery, when external power is not available. In this mode it draws 3.5 ma which should give you more than 250 hours of operation off of a new battery. If phantom power is available, then the Xdirect will automatically draw its power from the external source. The battery on/off switch lights dim when the unit is running off of the battery, lights brightly when it is running off of phantom power, and is off when the unit is inactive.

The compact black anodized all aluminum case and it's flexible power design allow the Xdirect to provide years of trouble free service in live sound, permanent/fixed install, DJ, and virtually any PA application. It's full feature set, rugged construction, and high-end specifications make the Xdirect the obvious choice whenever you have to interface high impedance sources with a low noise balanced system.

Passive interface lets you connect instrument, line, or speaker level signals to a mixer or other balanced input thru an audio isolation transformer

Review: The Zdirect is a high quality totally passive interface that lets you connect instrument, line, or speaker level signals to a mixer or other balanced input thru a high performance audio isolation transformer. The high impedance single-ended 1/4" input is converted by the transformer into an isolated balanced low impedance signal source. The Zdirect's audio transformer has an extremely flat and wide frequency response and can handle high signal levels while still maintaining an isolated balanced low impedance output. This gives the Zdirect a very clean and neutral sound with a wide variety of signal sources and over long signal runs in high noise environments.

The input attenuator switches allow for a wide range of signal levels and the input thru jack allows for tapping off of your signal chain. The ground lift switch lets you totally separate the input and output signal grounds, when appropriate, to isolate 2 systems, thereby reducing hum and ground-loop noise.

What further sets the Zdirect apart from other DI boxes are its extended features and versatility. ART have added a switchable low pass filter that cuts out all very high frequency interference. This Bessel filter on the output is placed out of the audio range and is primarily intended to reduce radio frequency interference before it gets into the main system. The filter is also very effective in reducing any digital computer noise artifacts when using the Zdirect as an interface between a computer-based audio workstation and your monitors. The phase invert switch, while not normally included with your run of the mill DI box, has been added to allow you to switch signal polarity right at the source. This feature is especially handy when you are combining a direct tap with a microphone feed in the mix.

The compact black anodized all aluminum case and it's passive design allow the Zdirect to provide years of trouble free service in Live Sound, Permanent/Fixed Install, DJ, and virtually any PA application. It's full feature set, rugged construction, and high-end specifications make the Zdirect the obvious choice.